기본 콘텐츠로 건너뛰기

리튬 배터리의 BMS 및 PCB는 무엇입니까? 왜 리튬 배터리가 필요합니까? Posted by batterymanufactory.com

BMS is battery management system, always for big battery packs, typical use is LiFePO4 power battery.It has protective functions of over charging,over discharging,over current,short-circuit, cells balancing functions,some battery may need also communication port and data input output options and other display functions. its up to applications requirements.

리튬 전지

PCB or PCM is protection circuit board, usually for small battery, typical use is for digital batteries, like mobile phone battery,camera battery,mp3 player battery,GPS batteries,heated clothing batteries and so on. Most time, Its for 3.7V or 7.4V battery, It has four basic functions of over charging, over discharging, short circuit,over current.some batteries may also need PTC and NTC.

Anode of rechargeable lithium battery mostly is made of Lithium ion material, the Li electron goes to both anode  and cathode sides once and once again during charging and discharging process,this how it works.In case of over charging,(lithium ion battery can not allow the cell voltage to be higher than 4.25v) the anode tiny hole structure may collapse, hard crystals substances may grow up and cause short circuit, then the temperature will rise up quickly, at last it will lead to a fire.So, over charging protection is needed.

As for short circuit and over current, it’s easy to understand, because in these cases, the internal temperature will be higher and higher, and catch a fire in the battery.

About over discharging, it’s also needs to be avoided, because lithium ion battery can lose large ratio of capacity forever once it was discharged to be too low level, for lithium ion battery cell, the voltage must be higher than 2.7V, if the voltage gets lower than this, eternal damage will happen to the battery.

So at least PCB/PCM must be used for lithium ion battery with basic protections, however for bigger lithium battery packs, it involves lots of battery cells, the unbalance of cells will also cause problems, such as shorter cycle life, low voltage, so on base of above mentioned four protections, balance function is added to make a basic BMS.

Tags:

Posted in 자주 묻는 질문 | 중국 리튬 폴리머 배터리 제조 업체, 리튬 이온 배터리, RC 사러 배터리 팩, 한 LiFePO4 배터리 팩 By

batterymanufactory.com

 

 BENZO 에너지 과학 기술 유한 회사



전화 번호   전화 번호：+86-755-84822012
전화 번호   전화 번호：+86-13538185686

E 메일   E 메일: contact@benzobattery.com
skype  Skype: benzobattery1231@gmail.com

사무실 주소   사무실 주소：  廣東省深圳市龍崗區阪田和成世紀名園
공장 주소   공장 주소：  廣東省東莞市清溪鎮羅馬路漢通科技園B1棟

         사이트：   bz-battery.en.alibaba.com   /   www.bz-battery.com

 

댓글

댓글 쓰기

이 블로그의 인기 게시물

스마트폰을 위한 어떤 종류의 배터리가 더 좋은가요? Li-Ion 또는 LiPo?

이미지
Did you ever think about why your phone works at all? Probably not. But, if you think about it, all portable gadgets rely on a battery to keep ticking – and some have better battery life than others. That’s why we’re going to take a peek at what keeps your phone ticking and why some batteries do better than others. On the basis of chemistry used for ions carrying electrolyte material, Lithium battery can be classified into Lithium ion and lithium Polymer. Lithium ion battery uses liquid lithium ion as electrolyte while lithium polymer use solid or gelatin like polymers as electrolyte. Lithium ion batteries have high energy density and cost less than lithium polymer. Lithium polymer batteries are light weight and have improved safety . However their cost is high (30% average) as compared to lithium ion. Also the the energy density of Li-Polymer battery compared to Li-Ion Batteries is quite less. Lithium ion batteries tend to lose charge with ageing even when not us...
자세한 내용 보기

What is KC certification? What are the requirements for the factory to pass the KC certification? Posted by batterymanufactory.com

이미지
What is KC certification? The KC (Korea Certification) certification mark signifies compliance with Korea’s product safety requirements for electrical and electronic equipment and components that utilise power from AC 50-1000V. The KC certification procedure for products includes the following steps: 1. Application - The application process involves the submission of an application form and product description. In addition, the manufacture must obtain a certificate of registration. 2. Factory inspection - Production equipment and processes are inspected and audited for compliance with applicable safety criteria. 3. Product testing - The product is tested consistent with the requirements of the applicable safety standard(s). 4. EMC testing - The product is tested for electromagnetic compatibility (EMC) and immunity. 5. Post-certification surveillance - Regular factory inspections and market surveillance are required to verify continued compliance following cer...
자세한 내용 보기

신기술로 인해 배터리가 코발트에서 분리 될 수 있습니다. Posted by batterymanufactory.com

이미지
Lithium-based batteries use more than 50 percent of all cobalt produced in the world. These batteries are in your cell phone, laptop and maybe even your car. About 50 percent of the world's cobalt comes from the Congo, where it's largely mined by hand, in some instances by children. But now, a research team led by scientists at the University of California, Berkeley, has opened the door to using other metals in lithium-based batteries, and have built cathodes with 50 percent more lithium-storage capacity than conventional materials. "We've opened up a new chemical space for battery technology," said senior author Gerbrand Ceder, professor in the Department of Materials Science and Engineering at Berkeley. "For the first time we have a really cheap element that can do a lot of electron exchange in batteries." The study will be published in the April 12 edition of the journal Nature. The work was a collaboration between scientists at...
자세한 내용 보기